Hiddens Falls May 20-22nd, Marble Falls, TX

tiresmokintacoma

Bean & Cheese TACO!
Here it is
attachment.php

attachment.php

attachment.php

attachment.php
 

Silverback

Lima Gulf Bravo Foxtrot Juliet Bravo
Ahh.. the one I know of the guy wants a V8.
 

tiresmokintacoma

Bean & Cheese TACO!
ahh well that sucks... Ill put my car up on the market and see what I can get.
 

yotarob

Kiss My IFS
Put that 302 in first
 

tiresmokintacoma

Bean & Cheese TACO!
swapping motors is a pain in the ass. I have done it 3 times with these fox bodies. Gotta change wireharness, fuel lines, rear end, and some other little stupid stuff. And if I ever do swap it out i will be keeping it.
 

tex

That's Mr Asshole to you
Having that 4cyl in there is really going to hurt the resale. However since you have the v8 it will help to sweeten the deal. You can get a trail rig for a few grand.
 

Anathollo

Armorall is my choice of lube
Staff member
Damn, wish I could make it but ill be at LSU watching my buddy graduate.
 

tiresmokintacoma

Bean & Cheese TACO!
Make sure u have sliders. And a locker if u don't already. A cb will help as well.
 

woody6047

Active Member
Make sure u have sliders. And a locker if u don't already. A cb will help as well.

I have sliders in the garage, i just have to weld em on and a lunchbox locker in the rear. Im gonna look into a cb. It just sucks because i have to wait till i get back from Iraq before i can get to it
 

taco4x4rar

Well-Known Member
I have sliders in the garage, i just have to weld em on and a lunchbox locker in the rear. Im gonna look into a cb. It just sucks because i have to wait till i get back from Iraq before i can get to it

I wouldn't go out there if I didn't have sliders or skids for that matter my trans pan has a hole in it cause I didn't have a skid covering it
 

tex

That's Mr Asshole to you
I have sliders in the garage, i just have to weld em on and a lunchbox locker in the rear. Im gonna look into a cb. It just sucks because i have to wait till i get back from Iraq before i can get to it

My truck is stock except for tires and I will not take it back out on the trails till I have sliders. I would make getting those on your truck the first thing you do before getting anything else ready. If you dont have time to install a CB, pick up a hand held unit.
 

woody6047

Active Member
I wouldn't go out there if I didn't have sliders or skids for that matter my trans pan has a hole in it cause I didn't have a skid covering it
I have a IFS skid, but im gonna pick up a tranny skid as well.

My truck is stock except for tires and I will not take it back out on the trails till I have sliders. I would make getting those on your truck the first thing you do before getting anything else ready. If you dont have time to install a CB, pick up a hand held unit.
Ill be getting back early May so I should have enough time to get everything on. Need to look up a little bit about CB stuff though
 

tex

That's Mr Asshole to you
I have a IFS skid, but im gonna pick up a tranny skid as well.


Ill be getting back early May so I should have enough time to get everything on. Need to look up a little bit about CB stuff though

CB Stuff is pretty easy. I knew nothing about till last summer. Still don't know that much but enough to install one in my truck. I think I did a write up around here somewhere. If you go with a fiberglass antenna get a firestick or if you go magnetic get a wilson. Make sure your antenna has a good ground and you should be good to go.
 
Top