Tools!
- Thread starter Silverback
- Start date
Silverback
Lima Gulf Bravo Foxtrot Juliet Bravo
I have way more impacts than just 3. 
Don't have 12 angle grinders... only 6 or 7. 
Don't have 12 angle grinders... only 6 or 7. 
Some stuff came together this month, so as a present to myself for all my hard work, I ordered a Modlite PLH-V2 as a handheld light. This is Modlite's version #2 of their PLH light head line. The light head has a more focused center beam with a large wash surrounding the beam. The beam isn't as intense as their OKW light but it's great for a handheld.
I also picked up the Thyrm 2.0 ring & clip for it as well. Makes it easier to pull the flashlight out of your pocket. I also use it to hold onto the light when I go on morning runs. However, I still think the circle finger ring is way too large and could be made smaller so it would fit into pockets better. It's taken a little while but I've gotten used to carrying it around.
I'm really digging this light right now because it also doubles as a weapon. If someone shines this light into your face, you'll be blinded for awhile as it's like looking at the sun It's also pretty hefty if you wanted to smack somebody with it as well.
I also picked up the Thyrm 2.0 ring & clip for it as well. Makes it easier to pull the flashlight out of your pocket. I also use it to hold onto the light when I go on morning runs. However, I still think the circle finger ring is way too large and could be made smaller so it would fit into pockets better. It's taken a little while but I've gotten used to carrying it around.
I'm really digging this light right now because it also doubles as a weapon. If someone shines this light into your face, you'll be blinded for awhile as it's like looking at the sun
It's also pretty hefty if you wanted to smack somebody with it as well. 
Taco Loco
Tired and Lazy, married to ‘The Laundry Fairy’
Drug the disc out, the one I brought home from the ranch back in January, pressure washed it, greased all the zerks/axle housings, 3 tubes of grease later and I noticed that 2 of the axle housings(clam shells) were installed wrong, I have owned this for ~15yrs and just realized that.
On disc/harrows all the zerks should be facing the rear, as you pull the disc, you don’t want debris breaking off the zerks. Flipped the axle clam housings 180* and then regressed them again. Also since this tractor has the 3pt quick release, I had to change out the lift pins to the larger pins.
larger lift pins
I really wish I had this up in running before I did my Victory garden area a month ago, oh well.
Three test paths near my Victory Garden, the real test will be on the 7acs down the road from me, neighbor wants me manage her property for her horses, it needs a lot of work.
On disc/harrows all the zerks should be facing the rear, as you pull the disc, you don’t want debris breaking off the zerks. Flipped the axle clam housings 180* and then regressed them again. Also since this tractor has the 3pt quick release, I had to change out the lift pins to the larger pins.
larger lift pins
I really wish I had this up in running before I did my Victory garden area a month ago, oh well.
Three test paths near my Victory Garden, the real test will be on the 7acs down the road from me, neighbor wants me manage her property for her horses, it needs a lot of work.
Last edited:
TacoXpo
HOAX DENIER
CowboyTaco
Well-Known Member
This piece fell off my miter saw when I was blowing off the sawdust. Where does it go?
Silverback
Lima Gulf Bravo Foxtrot Juliet Bravo
Its a carry handle for a female. One in the pink one in the stink.
Maybe the saw dust bag??
Oswego
n00b
Somethings eating that saw from within. Look at the miter guide slot - it's chewing itself up. Little yellow plastic shards from it are sitting on the fence. Never seen that in all my life and Ive broken more than a couple miter saws
Maybe a loose blade?
Whatever it is - stop using it till you fully inspect it. Somethings seriously wrong IMHO ~ Nothing should be breaking the slot plastic let alone chewing it up and spitting it out like that.
CowboyTaco
Well-Known Member
I think you're looking at the picture wrong, or maybe its a poor picture. That piece you circled is not from the deck.
Oswego
n00b
whatever it is it should not be there (part labeled fubar) so I'd give it a good once over especially if other parts are coming off. May be an offcut trapped under the miter slot?
Is the miter gauge clicking in fine? That spring maybe one of the stops that got "moved" when that offcut hit it. IDK man, thats my best guess and I worked on DeWalt miter saws for more than a few years cutting on them every M-F for 8+hrs a day.
Is the miter gauge clicking in fine? That spring maybe one of the stops that got "moved" when that offcut hit it. IDK man, thats my best guess and I worked on DeWalt miter saws for more than a few years cutting on them every M-F for 8+hrs a day.
Silverback
Lima Gulf Bravo Foxtrot Juliet Bravo
What brand is that? DeWalt?
Silverback
Lima Gulf Bravo Foxtrot Juliet Bravo
Right.. same thought.
I am betting its from something else and just happened to land on the miter saw.
https://chainsawjournal-wpengine.ne...ads/2016/08/MANUAL-DEWALT-DW715-miter-saw.pdf
I am betting its from something else and just happened to land on the miter saw.
https://chainsawjournal-wpengine.ne...ads/2016/08/MANUAL-DEWALT-DW715-miter-saw.pdf